国产无码久久久,日韩男女日b视频,久久精品无码专区免费九九,成人电影一区二区三区电影

Online Service
Scan it
Support hotline
18681482740
Service Hotline:
18681482740
中文  |   English
News
Contact

Address: Floor 1, Building 2, Quanshengchang Industrial Park, Buyong Shajing Road, Shajing Street, Shenzhen

Contact: Mr. Li 18681482740

Email: lilinhan1314@126.com

Website: shclgm.com.cn

News
Analysis of Common Faults of Hardware Stamping Parts
03-15 / 2024

Hardware stamping is the first of the four main processes, and its importance can be imagined. The quality of the finished products from Shenzhen Hardware Stamping Factory will lay a solid foundation for the appearance and performance of the entire vehicle. Therefore, the quality assurance of stamping parts has always been a highly valued issue for automotive manufacturing enterprises. Based on the practical experience of quality management in stamping factories in China, the editor summarized common causes and countermeasures in the production process of metal stamping parts, hoping to provide some useful references for improving the quality of stamping parts.


Why does metal stamping parts exhibit steering distortion?


In progressive dies, metal stamping components form the shape of the punch by stamping the residual material around the stamping component. Stamping materials produce turning materials The main reason for distortion is the impact of impact pressure. During stamping, due to the presence of stamping gaps, the material is stretched (warped upwards) on one side of the mold and compressed on the punch side. When using the unloading plate, the material is squeezed by the unloading plate to prevent the material on the side of the mold from warping upwards. At this point, the stress state of the material changes accordingly. As the material increases through the discharge plate, the material on the punch side is stretched (the compressive force tends to decrease), and the material on the mold surface is compressed (the tensile force tends to decrease). The reversal of stamping is due to the stretching of the material on the mold surface. Therefore, when stamping, pressing and pressing the material is the key to preventing the punch from flipping. Reasons and countermeasures for bending and stamping during the bending process. 1. Caused by burrs generated by stamping. It is necessary to study the cutting-edge and pay attention to checking whether the punching gap is reasonable. During the punching process, stamping of stamping components was generated Distortion, resulting in poor forming after bending, needs to be addressed from the punching and unloading stations. Due to three bends, the stamped part is unstable. Mainly used for U-shaped and V-shaped bending. The handling of this issue is focused on bending the guide before impact during the bending process, which leads to material compression during the bending process to prevent the stamping components from sliding during the bending process.


Why can metal stamping components cause tearing? The stamping process for the middle panel bracket of metal stamping parts with common tearing and skewed shapes is: punching, punching, cutting, flanging, forming, cutting, and flanging. During the formation of the intermediate support, there are various forms of tearing and tilting. Due to stamping and production, the torn part is mainly distributed at the intersection of the hole shape, R-arc, and wall neck at the corner of the sidewall of the component. The differences in process conditions vary in the proportion of each fracture site. Tear can be a one-time tear, or it can be caused by fatigue cracks, i.e. the formation of invisible cracks. Based on the actual situation on site, the cause was analyzed and the tearing of the workpiece was determined to be, by examining the fracture shape and degree of fragmentation of the workpiece. Skew behavior is mainly reflected in the formation process of flipping. The reasons for this process are as follows:



1. The molding process parameters are not in place. In the process of forming parts, the mold, pressure core, and two parts must be tightly connected, and when the machine slider slides downwards, the plastic deformation of the paper is forced. Forming.


Hardware stamping parts | Hardware stamping terminals | Automotive hardware parts | Precision wire drawing parts | Motor chips | New


Links:Zibo CNC machine tool automatic car washing machine Qingdao refrigeration equipment grinder equipment steel grit fire inspection cabinet sweeper motor desulfurization denitrification equipment drawing mold washing machine automatic soldering machine server repair HART475 hand operator dust-free cloth dust-free paper stack screw type Sludge dehydration machine, precision repair welding machine, Shandong motor repair, rotary hot pot equipment, integrated ultrasonic cleaning machine, Zhongjie radial drilling machine, beer equipment, Shenzhen brass manufacturer, welcome lamp, lens digging, drilling rig, aluminum housing manufacturer, automatic dispensing machine, automatic screwing machine neodymium Iron boron magnet 4g router wireless bridge
We provide you with high quality products
国产91大肉棒| 嗯嗯啊嗯嗯啊啊在线观看| 国产精品视频色拍拍| 性色av色哟哟| 91网站后入不卡高清在线观看视频| 92国产精品久久久青青| 色秘 乱码一区二区三区在线| 男人天堂网址| 国产秋霞综合区| 超碰国内香蕉| H日韩欧美区| 成人电影 一区二区三区| 国产一本一区| 成人久久大香蕉视频| 嗯嗯视频免费看| 久久婷婷伦理图库| 日韩视频一区二区三区四区| 不卡二区精品| 亚洲夜间伦理在线| 国产一区在线免费av| 亚洲日韩一区二区三区综合| 国产欧美日韩性爱| 91啪国自产中文字幕| 国产精品一区自拍女同| zoo丝袜一区二区| Pornh一区二区| 爱操免费视频| 亚洲少妇90p| 乱老女人一二区视频| 欧美日韩国产专区一区二区| 99玖久久久久国内精品| 欧美激情四区七区六区| 欧美黄片怎么找| 夫妻网日韩久久| 男女激情啪啪大屌网站| 中文字久久9| 啪啪啪免费网站亚洲精品| 日本道三区色WWW| 老色批久久综合| 天天干天天操天天草| 黄色在线播|